Get a fast start on your next paper mache project or hand-made gift with Jonni’s easy downloadable patterns for masks, animal sculptures and faux trophy mounts. The patterns help you create a beautiful work of art, even if you’ve never sculpted anything before.
Important Note: I used drywall (plaster board) for the pattern on this project, just to see if it would work. It didn’t! Use cardboard, instead. I also used Super Sculpey as the form for the head and I forgot to remove it after the paper mache was dry, like I should have. The oil in the modeling clay seeped through the paint and ruined part of his face. It took about a year for the spot to show, but then it just kept getting bigger. I also used Super Sculpey for my giraffe head -but I did it right that time, and cut the head open to remove the clay. Live and learn. 😉
A recent visitor asked for some tips for making a paper mache horse for her daughter. I’ve never made one, but I think my grandson would love one for his room, too.
I chose an appaloosa foal for my sculpture for two reasons –
- I love the long legs on a new colt, even though they’re going to cause some problems with this project.
- And the spots on an appaloosa are so adorable!
I decided to go ahead and let you “watch” the project in process so you can see problems as they arise. This will show you how I come up with ideas that, hopefully, make things work. Of course there’s never just one good way to do things, and I quite often try things one way and then end up doing them over. For that reason, you might want to hold off on copying my project until the final post…
The beginning of any project is always a bit scary, because there’s a lot of engineering involved – and I didn’t pay much attention in my math and science classes.
In the photo above you can see that I made a sketch of a colt, using as inspiration an art book that I’ve had for years and some photos I found on the Internet. In the sketch you can clearly see the shoulder and hip bones, and how they affect the shape of the body. (For more info on this issue, see my recent post on basic anatomy for paper mache animal sculptures).
If you’d like to use the pattern I made (it’s a bit rough, but it works) you can download the image of the horse pattern here.
Whenever you do a three-dimensional sculpture based on two-dimensional photos, you need to find as many photos as you can so you can see the animal from all sides.
Another thing to pay attention to, especially with a young animal, is to make sure all your models are about the same age. Of course if you have an actual colt in your backyard, be sure to use him for your model. I’m not so lucky…
My Sketch of an Appaloosa Colt
I don’t normally make a full sized drawing ofÂ my sculptures. In fact, a lot of times I don’t make any sketches at all. However, the legs on this colt are going to give me difficulties so I decided to make a drawing the exact size of the finished piece. I’ll be using the full-sized drawing as a pattern for the legs.
To make the original drawing larger, I drew a grid on my original sketch with one-inch squares, and then drew a grid with two-inch squares on a large piece of brown paper. Using the grids, I reproduced my original drawing twice as high and wide as the original. The second sketch is about 23 inches high. I thought this would be a fairly respectable sized paper mache horse for a little boy’s bedroom.
Leg Problem #1 – Stability:
I know I can’t make the legs hollow and pour plaster in the bottom of the legs to keep the colt from falling over, like I did with the giraffe, because the legs are too thin. That means the sculpture will be top-heavy and it will fall over at the slightest nudge unless I find a way to make the legs heavier than the body and the head. It would be even better to just make the bottom half of the legs heavy, but I couldn’t figure out a way to do that.
Leg Problem #2 – Safety:
Since the legs are thin, they need to be made quite strong in order to hold up the sculpture. However, many options I considered for strengthening the legs got rejected because the finished piece may be in a toddler’s bedroom, and safety is my primary concern.
If I used wire as an armature in the legs and my grandson fell against the sculpture or jumped on it, the wire could break through the paper mache and poke him. Not good.
The same thing could happen if I cut wood pieces to go inside the legs – if my grandson fell against the colt the wood inside the legs might break, making them sharp and potentially lethal.
The solution I came up with is not the best, but I think it will work. I’ll be making the legs out of plaster board (wall board) inside the paper mache. Plaster board is a little bit heavier than cardboard (another option), but it’s not very strong and has no real structural strength, especially when it’s cut so thin. However, I think the paper mache layers on top will make it strong enough to hold up the colt.
And if my grandson does break one of the colt’s legs there won’t be anything inside that could cause him an injury. The plaster board will just bend or crumble.
I used my full-sized drawing as a pattern for the legs, which I cut out of a scrap of plaster board with a jig saw. Now my problem is to round off the corners without breaking the legs, since all the strength in this material is in the paper that holds it together.Â Tomorrow you should be able to see if I succeeded, or if I have a pile of plaster on my work bench… Wish me luck.
- Paper Mache Colt, Lesson #2 – adding crumpled paper to the armature
- Paper Mache Colt, Lesson #3 – finishing the legs
- Paper Mache Colt, Lesson #4 – adding paper strips and paste
- Paper Mache Colt, (had to redo a few things – not really a lesson, just a boo boo…
- Paper Mache Colt, Lesson #5 – modeling the head with Super Sculpey
- Paper Mache Colt, Lesson #6 – Painting the sculpture